Laffs PDW XL Sights: Laffs Dynamics
Taller variant of the original 3FTech/Laffs PDW Sights.
Have gotten numerous requests for a slightly taller version over last couple years.
Raised it up 8mm. Still uses previous version's swappable rear sight inserts and same set screw for the front sight post.
Three rear drift sights are available:
*4mm U Notch
*5mm U Notch
*5.5mm Aperture
Note: For those people that wanted it "AR" height... no :3 I aint raising them up 30mm+. They meant for guns like the Scorpion Evo 3, PS90,
GHM9, and Stribog SP9. These sights are not percise enough for carbine use and I don't wanna hear people complain about accuracy if I made
such a variant. They're fine for PDW/SMG/PCC usage.
Original Laffs PDW Sights files can be found on DefCAD:
Link: https://defcad.com/library/51bd2005-1f97-4ab9-8e4d-2a320bcd4ba0/
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40mm
Wall Perimeters: 6+
Infill: 38%+
Support Material Percentage: 20%
Print the front and rear sight mounts on their front faces, and the rear sight drift on it's rear, flattest face.
Hardware Needed:
2x M5x30 Hex Socketed Machine Screw/Bolt
2x M5 Hex Nut (Be sure both bolt & nut are the same thread pitch.)
1x M3x10 Set Screw
File | Extension |
---|---|
Laffs PDW XL Sights.zip | zip |
Version: 1.0.0 latest
initial upload
Laffs PDW XL Sights: Laffs Dynamics
Taller variant of the original 3FTech/Laffs PDW Sights.
Have gotten numerous requests for a slightly taller version over last couple years.
Raised it up 8mm. Still uses previous version's swappable rear sight inserts and same set screw for the front sight post.
Three rear drift sights are available:
*4mm U Notch
*5mm U Notch
*5.5mm Aperture
Note: For those people that wanted it "AR" height... no :3 I aint raising them up 30mm+. They meant for guns like the Scorpion Evo 3, PS90,
GHM9, and Stribog SP9. These sights are not percise enough for carbine use and I don't wanna hear people complain about accuracy if I made
such a variant. They're fine for PDW/SMG/PCC usage.
Original Laffs PDW Sights files can be found on DefCAD:
Link: https://defcad.com/library/51bd2005-1f97-4ab9-8e4d-2a320bcd4ba0/
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40mm
Wall Perimeters: 6+
Infill: 38%+
Support Material Percentage: 20%
Print the front and rear sight mounts on their front faces, and the rear sight drift on it's rear, flattest face.
Hardware Needed:
2x M5x30 Hex Socketed Machine Screw/Bolt
2x M5 Hex Nut (Be sure both bolt & nut are the same thread pitch.)
1x M3x10 Set Screw
1.8K
239
Feb 28, 2024
3D Printer
United States
English
Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International
File | Extension |
---|---|
Laffs PDW XL Sights.zip | zip |
Version: 1.0.0 latest
initial upload
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.