3FTech Picatinny Handstop
about
3FTech Picatinny Handstop: FFFTech/FFFTechnology
...It's a handstop that mounts to picatinny rails...
Were you expecting some deep lore?
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40mm
Wall Perimeters: 4+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the handstop upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm so it doesn't stick out the side)
1x M4 Hex Nut
files
| File | Extension |
|---|---|
| Laffs Picatinny Handstop V1.1.2.zip | zip |
versions
Version: Laffs Picatinny Handstop V1.1.2 latest
Laffs Picatinny Handstop V1.1.2: Laffs Dynamics
...It's a handstop that mounts to picatinny rails...
Were you expecting some deep lore?
Update V1.1.2: Redesignated the design. Relabeled designer name. Loosened picatinny channel dimensions.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40mm
Wall Perimeters: 4+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the handstop upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm so it doesn't stick out the side)
1x M4 Hex Nut
Version: 1.0.0
Initial release
about
3FTech Picatinny Handstop: FFFTech/FFFTechnology
...It's a handstop that mounts to picatinny rails...
Were you expecting some deep lore?
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40mm
Wall Perimeters: 4+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the handstop upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm so it doesn't stick out the side)
1x M4 Hex Nut
creator
Metrics
Views
2.2K
Downloads
651
Project Info
release date
Oct 17, 2022
artifact type
Printable project
library category
Printable Peripherals / Parts
fabrication method
Primarily Printable
fabrication tool
3D Printer
release country
United States
language
English
license
files
| File | Extension |
|---|---|
| Laffs Picatinny Handstop V1.1.2.zip | zip |
versions
Version: Laffs Picatinny Handstop V1.1.2 latest
Laffs Picatinny Handstop V1.1.2: Laffs Dynamics
...It's a handstop that mounts to picatinny rails...
Were you expecting some deep lore?
Update V1.1.2: Redesignated the design. Relabeled designer name. Loosened picatinny channel dimensions.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40mm
Wall Perimeters: 4+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the handstop upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm so it doesn't stick out the side)
1x M4 Hex Nut
Version: 1.0.0
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.
