10/22 Dust Devil Flash Suppressor: FFFTech/FFFTechnology
A short, five prong rounded conical flash suppressor. Prongs twist anti/counter-clockwise. (Viewed from the front.)
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .18mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 7+
Infill: 50%
Infill Pattern: Gyroid
Material Flow: 100%
Hardware Needed:
1x M3x16 Set Screw
SAFETY NOTE: Due to this design coming into contact with hot metal and gasses, it's HIGHLY recommended to
print the design, and use Lost PLA Casting in metal for the finished object. The printed version CAN be
used, but should not be expected to retain structural rigidity for more than a few dozen rounds fired.
File | Extension |
---|---|
22 Dust Devil Flash Suppressor V1.0.2/10-22 Dust Devil FS V1.0.2.zip | zip |
Version: 10/22 Dust Devil Flash Suppressor V1.0.2 latest
10/22 Dust Devil Flash Suppressor V1.0.2: Laffs Dynamics
A short, five prong rounded conical flash suppressor. Prongs twist anti/counter-clockwise. (Viewed from the front.)
Update V1.0.2: Changed designer name, changed recommended printer and print settings to the commonly used Ender 3.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 6
Infill: 100%
Hardware Needed:
1x M3x16 Set Screw
SAFETY NOTE: Due to this design coming into contact with hot metal and gasses, it's HIGHLY recommended to
print the design, and use Lost PLA Casting in metal for the finished object. The printed version CAN be
used, but should not be expected to retain structural rigidity for more than a few dozen rounds fired.
Version: 1.0.0
Initial release
10/22 Dust Devil Flash Suppressor: FFFTech/FFFTechnology
A short, five prong rounded conical flash suppressor. Prongs twist anti/counter-clockwise. (Viewed from the front.)
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .18mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 7+
Infill: 50%
Infill Pattern: Gyroid
Material Flow: 100%
Hardware Needed:
1x M3x16 Set Screw
SAFETY NOTE: Due to this design coming into contact with hot metal and gasses, it's HIGHLY recommended to
print the design, and use Lost PLA Casting in metal for the finished object. The printed version CAN be
used, but should not be expected to retain structural rigidity for more than a few dozen rounds fired.
2.2K
201
Mar 16, 2023
3D Printer
United States
English
File | Extension |
---|---|
22 Dust Devil Flash Suppressor V1.0.2/10-22 Dust Devil FS V1.0.2.zip | zip |
Version: 10/22 Dust Devil Flash Suppressor V1.0.2 latest
10/22 Dust Devil Flash Suppressor V1.0.2: Laffs Dynamics
A short, five prong rounded conical flash suppressor. Prongs twist anti/counter-clockwise. (Viewed from the front.)
Update V1.0.2: Changed designer name, changed recommended printer and print settings to the commonly used Ender 3.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 6
Infill: 100%
Hardware Needed:
1x M3x16 Set Screw
SAFETY NOTE: Due to this design coming into contact with hot metal and gasses, it's HIGHLY recommended to
print the design, and use Lost PLA Casting in metal for the finished object. The printed version CAN be
used, but should not be expected to retain structural rigidity for more than a few dozen rounds fired.
Version: 1.0.0
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.