Glock 17 Picatinny Adaptor Rail by FFFTech/FFFTechnology
Compatible with Gen 4 Glock 17 frames, as well as Glock models that share the same frame such as: Glock 17L, 22, 31, 34, 35 and 37.
A six slotted picatinny rail that attaches to the Glock 17 proprietary rail. While most picatinny compatible accessories will fit on the glock rail, the single slot limits the options when one wishes to move accessories forward and back on the rail. Should one wish to turn their Glock into an SBR, the adaptor is long enough (and has enough slots) to facilitate a foregrip. The rail extends all the way to the front of the triggerguard, and the front protrudes only slightly, being flush with the front of the slide.
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 204C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 3
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 10%
Support material only for the rail slots directly above the print bed.
Hardware Needed:
1x M4x10mm Hex Socketed Set Screw
Installation:
1) After support material removal, slide the picatinny adaptor over the Glock Rail.
2) Hold the rail to it's rearmost position and start threading the set screw into the adaptor.
3) Drive the set screw flush with the bottom of rail slot. Check every 2 screw revolutions to see if the rail adaptor is properly secure.
4) Once secure, attach dem bomb diggity accessories.
File | Extension |
---|---|
Glock 17 Picatinny Adaptor Rail.zip | zip |
Version: V1.5 latest
Glock 17 Picatinny Adaptor Rail V1.5 by FFFTech/FFFTechnology
The following description is for V1.5, but the files for V1 are still included in the .zip file, with V1.5 files as well.
Compatible with Gen 3 & Gen 4 Glock 17 frames, as well as Glock models that share the same frame such as: Glock 17L, 22, 31, 34, 35 and 37.
An updated design of the original Glock 17 Picatinny Adaptor Rail. Unneeded material has been removed from the internal structure, the edges of the picatinny rail channels have been scalloped, and overall height has been reduced by 1mm. Overall takes a few minutes less time to print, and needs a little material than the previous design.
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 204C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 3
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 10%
Support material only for the rail slots directly above the print bed.
Hardware Needed:
1x M4x10mm Hex Socketed Set Screw
Installation:
1) After support material removal, slide the picatinny adaptor over the Glock Rail.
2) Hold the rail to it's rearmost position and start threading the set screw into the adaptor.
3) Drive the set screw flush with the bottom of rail slot. Check every 2 screw revolutions to see if the rail adaptor is properly secure.
4) Once secure, attach dem bomb diggity accessories.
Version: 1.0.0
Initial release
Glock 17 Picatinny Adaptor Rail by FFFTech/FFFTechnology
Compatible with Gen 4 Glock 17 frames, as well as Glock models that share the same frame such as: Glock 17L, 22, 31, 34, 35 and 37.
A six slotted picatinny rail that attaches to the Glock 17 proprietary rail. While most picatinny compatible accessories will fit on the glock rail, the single slot limits the options when one wishes to move accessories forward and back on the rail. Should one wish to turn their Glock into an SBR, the adaptor is long enough (and has enough slots) to facilitate a foregrip. The rail extends all the way to the front of the triggerguard, and the front protrudes only slightly, being flush with the front of the slide.
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 204C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 3
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 10%
Support material only for the rail slots directly above the print bed.
Hardware Needed:
1x M4x10mm Hex Socketed Set Screw
Installation:
1) After support material removal, slide the picatinny adaptor over the Glock Rail.
2) Hold the rail to it's rearmost position and start threading the set screw into the adaptor.
3) Drive the set screw flush with the bottom of rail slot. Check every 2 screw revolutions to see if the rail adaptor is properly secure.
4) Once secure, attach dem bomb diggity accessories.
5.9K
611
Jul 02, 2021
Printable project
Printable Peripherals / Parts
Primarily Printable
United States
English
Pistol
Glock 17
Rail
QmVPyFtZj7j12Leuu8Hb2GMzNt3TCpy5JAqNHqFFbbkKBg
File | Extension |
---|---|
Glock 17 Picatinny Adaptor Rail.zip | zip |
Version: V1.5 latest
Glock 17 Picatinny Adaptor Rail V1.5 by FFFTech/FFFTechnology
The following description is for V1.5, but the files for V1 are still included in the .zip file, with V1.5 files as well.
Compatible with Gen 3 & Gen 4 Glock 17 frames, as well as Glock models that share the same frame such as: Glock 17L, 22, 31, 34, 35 and 37.
An updated design of the original Glock 17 Picatinny Adaptor Rail. Unneeded material has been removed from the internal structure, the edges of the picatinny rail channels have been scalloped, and overall height has been reduced by 1mm. Overall takes a few minutes less time to print, and needs a little material than the previous design.
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 204C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 3
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 10%
Support material only for the rail slots directly above the print bed.
Hardware Needed:
1x M4x10mm Hex Socketed Set Screw
Installation:
1) After support material removal, slide the picatinny adaptor over the Glock Rail.
2) Hold the rail to it's rearmost position and start threading the set screw into the adaptor.
3) Drive the set screw flush with the bottom of rail slot. Check every 2 screw revolutions to see if the rail adaptor is properly secure.
4) Once secure, attach dem bomb diggity accessories.
Version: 1.0.0
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.